- Seen : 361 View
Two-component polymer seal Tiva Polymer Flexible Cement Polymer Modified polymer, two-component cement used in liquid form, has a waterproof layer to protect concrete and mortar. Flexibility, excellent adhesion, durability and strength of crack coating are the features of this product. Cement polymer can be used in various cement surfaces, marine structures, basement insulation, wet areas insulation, roofs, pools, water tanks and..
The advantages of two-component pool insulation mortar include excellent traction and flexibility, non-toxicity, use in drinking water tanks, excellent adhesion and easy implementation. IZOcement is an ideal choice in this regard.
Using high technology of materials engineering shows that cement can be induced as a mineral binder with high elastic properties and it is protected from damage and cracking against building stresses.
Advantages of two-component polymer sealant for Tiwa pool over conventional insulation
Current insulation systems, which are made of pure organic materials, do not have good penetration and adhesion to cement and concrete surfaces.
Therefore, after a short time and after a period of cooling-heating (due to the mismatch of the heat capacity of cement and bitumen), they are easily separated from their subsurface. This gradually causes water to seep in and accumulate behind the insulation layer.
Also, in conventional systems, due to the lack of complete sealing, it is sufficient to have a small hole in the mortar for sealing the bathroom wall and services.
Water and steam penetrate into the body of the wall through this hole and gradually spread throughout the brick, and finally reach the back of the insulation in the floor, or steam collects from below the bathroom downstairs, and like isogum or gypsum in Can not withstand negative water pressure,
With building stresses, it loses its sealing power.
Due to the fact that in the slurry method, there is not enough adhesion between the tile and the slurry, the tiles are removed sooner than necessary.
Conventional insulation systems face difficulties due to the high thickness of the layer and the lack of flexibility in the insulation of the corners. After that, due to the overlap of the layers, the corners become uneven and distance from the wall surface behind. they take.
This causes the need to increase the volume of mortar with slurry tiling. Toilets face space constraints. The load on the building goes up. Sealing security is reduced.
Uses of Tiwa pool two-component polymer seal
Building foundations and basements, elevator shafts and catchments
Services such as bathroom, toilet, kitchen
Roofs and rain gutters
Moisture from external surfaces
Advantages of two-component polymer seal Tiwa pool
Its preparation and consumption is easy to make mortar
Its consumption does not require heat
It is applied as an integrated layer with sufficient adhesion to both sides under the work and on the work surface
It has the ability to paint
In addition to withstanding hydrostatic pressure (positive pressure), it also withstands negative pressure
It does not disrupt the layout of the following facilities.
The corners of the services can be sealed with all elegance
It is about 2-3 mm thick, which is applied in at least two layers at intervals of 2-5 hours
It can be done in horizontal and vertical planes.
Durability against heat, and extreme cold
Ease of repairs and increase the level of insulation
Applying a new layer of two-component pool insulation mortar on the floor, after tiling the wall, greatly increases the assurance of insulation.
Features of Tiwa pool two-component polymer seal
High durability: Two-component pool insulation mortar has good resistance to sunlight and does not suffer from cracking, dryness or separation from the substrate.
Ease of application of two-part pool insulation mortar: This product is supplied in two parts, including a cement component and a liquid polymer component. In a construction workshop, they are mixed together to produce a color-like compound. This product can be applied to the work with a brush or trowel and roller after preparation in the workshop.
In conventional waterproofing systems, first all the building services are insulated and then the tiler works on the body and floor tiles. Due to the low speed of tiling and its elongation, floor insulation is exposed to a variety of damages.
During this period, the possibility of falling sharp materials, passing workers with spiked shoes… has caused serious damage that only in the operation phase of the building can be realized that it must be repaired at a high cost.
In IZOcement insulation system, due to the ease of insulation, it can be done in two stages: one stage before wall tiling only includes wall and floor covering and the second stage on the floor and before floor tiling.
Lack of vulnerability of two-component pool insulation mortar: Common insulation is vulnerable to metals, nails and sharp materials, etc., and they are punctured very quickly, and usually repairs to perforated areas are not completely successful. Therefore, it is practically necessary for the initial insulation to be assembled and re-operated completely
Saler Company Information
